Results 1 to 3 of 3

Thread: Router Boot-up Process

  1. #1

    darani is offline
    Senior Member Array
    Join Date
    Nov 2006
    Country: India
    Rep Power

    Router Boot-up Process

    There are four major phases to the bootup process:
    1. Performing the POST
    2. Loading the bootstrap program
    3. Locating and loading the Cisco IOS software
    4. Locating and loading the startup configuration file or entering setup mode

    1. Performing the POST

    The Power-On Self Test (POST) is a common process that occurs on almost every computer during bootup. The POST process is used to test the router hardware. When the router is powered on, software on the ROM chip conducts the POST. During this self-test, the router executes diagnostics from ROM on several hardware components including the CPU, RAM, and NVRAM. After the POST has been completed, the router executes the bootstrap program.

    2. Loading the Bootstrap Program
    After the POST, the bootstrap program is copied from ROM into RAM. Once in RAM, the CPU executes the instructions in the bootstrap program. The main task of the bootstrap program is to locate the Cisco IOS and load it into RAM.
    Note: At this point, if you have a console connection to the router, you will begin to see output on the screen.

    3. Locating and Loading Cisco IOS
    Locating the Cisco IOS software. The IOS is typically stored in flash memory, but can also be stored in other places such as a TFTP (Trivial File Transfer Protocol) server.
    If a full IOS image can not be located, a scaled-down version of the IOS is copied from ROM into RAM. This version of IOS is used to help diagnose any problems and can be used to load a complete version of the IOS into RAM.
    Note: A TFTP server is usually used as a backup server for IOS but it can also be used as a central point for storing and loading the IOS. IOS management and using the TFTP server is discussed in a later course.

    4. Locating and Loading the Configuration File
    Locating the Startup Configuration File. After the IOS is loaded, the bootstrap program searches for the startup configuration file, known as startup-config, in NVRAM. This file has the previously saved configuration commands and parameters including:

    * interface addresses
    * routing information
    * passwords
    * any other configurations saved by the network administrator

    If the startup configuration file, startup-config, is located in NVRAM, it is copied into RAM as the running configuration file, running-config.
    Executing the Configuration File. If a startup configuration file is found in NVRAM, the IOS loads it into RAM as the running-config and executes the commands in the file, one line at a time. The running-config file contains interface addresses, starts routing processes, configures router passwords and defines other characteristics of the router.

    Enter Setup Mode (Optional). If the startup configuration file can not be located, the router prompts the user to enter setup mode. Setup mode is a series of questions prompting the user for basic configuration information. Setup mode is not intended to be used to enter complex router configurations, and it is not commonly used by network administrators.
    When booting a router that does not contain a startup configuration file, you will see the following question after the IOS has been loaded:

    Command Line Interface
    Depending on the platform and IOS, the router may ask the following question before displaying the prompt:
    Would you like to terminate autoinstall? [yes]:
    Press the Enter key to accept the default answer.
    Note: If a startup configuration file was found, the running-config may contain a hostname and the prompt will display the hostname of the router.
    Once the prompt displays, the router is now running the IOS with the current running configuration file. The network administrator can now begin using IOS commands on this router

  2. #2
    Hey darani.., R u finished CCNA certification?

  3. #3
    Member Array
    Join Date
    Jul 2009
    Bhubaneswar, India, India
    Rep Power

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Topic on router
    By santosh9702 in forum Introduce yourself here
    Replies: 1
    Last Post: 02-26-2010, 01:01 PM
  2. Boot Skin - Change the old xp boot screen
    By admin in forum Desktop
    Replies: 3
    Last Post: 07-22-2009, 10:39 AM
  3. Netgear WGR614L Open Source Router
    By mrina in forum Gadgets
    Replies: 0
    Last Post: 07-02-2008, 12:47 PM
  4. Belkin N1 Vision Wireless Router launched in India
    By mrina in forum Computers and Laptops
    Replies: 0
    Last Post: 05-25-2008, 12:03 AM
  5. Router Commands Overview
    By darani in forum Computers and Laptops
    Replies: 4
    Last Post: 11-27-2007, 02:00 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Like us on Facebook | Get Website Updates | Get our E-Magazine

Get Daily Forum Updates

Get Most Amazing E-mails Daily
Full of amazing emails daily in your inbox
Join Nidokidos E-mail Magazine
Join Nidokidos Official Page on Facebook